DIY-Do-It-Yourself-Self-Installed Shower Drain-Bathroom Drain-Drainage System Installation-Setup-Project: How To-Tips for-Step-By-Step Guide

DIY-Do-It-Yourself-Self-Installed Shower Drain-Bathroom Drain-Drainage System Installation-Setup-Project: How To-Tips for-Step-By-Step Guide

Blog Article

Book Service

Nearly everybody will have their own idea when it comes to How to Install a Shower Drain.

Updating a shower room is just one of the more popular residence renovation tasks. Dealing with the plumbing for draining your shower can be exceptionally basic unless you overdo it.

Handling Your Own Shower Drain Setup Task

Whether you are a bathtub or shower person, many people look for shower only options when purchasing a house. This simple truth means greater than a few home owners spend a weekend break upgrading or setting up showers in their restrooms. Thankfully for you, it is a fairly easy process.

A collector or frying pan refers to the straight surface located at the bottom of the shower. The collector typically contains a non-slip surface area somewhat banked towards the center or any place the drain lies. Incorporated with three to 4 inch wall surfaces around the side, the goal of your shower water drainage plumbing is to get the water to move to and down the drain.

You can physically develop a collection agency for your new shower, but you really need to think about it. Do you actually intend to enter the problems of obtaining the sloping appropriate, not to mention seeing to it every aspect of it is water-proof? And also I indicate every aspect! It is a lot easier to merely purchase a pre-cast enthusiast online or at your local Lowes, House Depot or equipment shop. Structure one could seem like an excellent suggestion, yet you will possibly feel in a different way after a number of hrs.

No matter how you set about obtaining a pan, you need to make every effort to make use of one that has the drainpipe situated in the same place as the initial pan. Moving the drainpipe pipes can be a task, particularly if the contractor used an one-of-a-kind framework structure. If you are identified to move the drain, you are going to need to cut back the pipeline or extend it, which may mean destroying large portions of the floor. Rephrase, you are going to be looking at a numerous weekend project.

Presuming we have our drain aligned, the actual link is relatively simple. The drain pipeline should be encountering vertical approximately the collector. It will certainly typically look like a "U", which indicates it acts as a cleanout to maintain nasty smells from returning up from the drain. To attach the drain, you are mosting likely to create a water tight link between a drain cap on the top of the frying pan and the drain pipe. Solutions differ, but you are generally mosting likely to do this by putting a coupling item on the top of the drainage pipe. This is after that covered with gaskets and also actually screwed right into the drainpipe cap. The drainpipe cap ought to work as a locknut, to wit, it screws straight onto the coupling.

The difficult part of this process is getting your drainpipe cap to match a watertight setting in the frying pan. This is completed by backing off the drain cap as soon as you are sure everything fits together. Then, you placed plumbing technicians putty around the bottom of the cap and then screw it back on. The putty ought to develop a tight seal between the cap and the shower pan, which maintains water from flowing under it and also right into the mounting under the shower.

Obviously, restroom showers been available in a wide array of designs nowadays. If you acquire a collector, they almost always come with plumbing instructions or the store can note anything uncommon you should recognize. It seems intricate, however is commonly rather easy. Enjoy!

How to Replace a Shower Drain

When Replacing a Shower Drain is Necessary

If you see water damage in the drywall in the ceiling below the shower

If your old shower drain is showing signs of corrosion

If you want to replace your shower pan or base

How to Replace a Shower Drain

When a bathtub drain links, it’s normally possible to make the repair from inside the bathtub. Shower drains, however, are constructed differently. To correctly repair a shower drain, you typically need to either cut into the ceiling below the shower or shimmy into the crawlspace under the bathroom depending on where the shower is located. Here’s how to change a shower drain in 8 steps.

Cut into the drywall underneath your shower

o begin work on your shower drain, turn off all circuit breakers that control the lights and outlets in the bathroom you’re working on. Wearing a headlamp for light optimizes safety until you feel confident you know where all the wires are located.

Replacing a shower drain isn’t an impossible job, but it can present some challenges (especially if you’re inexperienced in plumbing projects). If you want to complete this task on your own, then it’s certainly possible. Follow this guide on how to change a shower drain.

When Replacing a Shower Drain is Necessary

How do you know when you should replace your shower drain? Here are some telltale signs.

If you see water damage in the drywall in the ceiling below the shower

If your old shower drain is showing signs of corrosion

If you want to replace your shower pan or base

The guide will help prepare you for the issues you may face during the process of replacing a shower drain.

How to Replace a Shower Drain

When a bathtub drain links, it’s normally possible to make the repair from inside the bathtub. Shower drains, however, are constructed differently. To correctly repair a shower drain, you typically need to either cut into the ceiling below the shower or shimmy into the crawlspace under the bathroom depending on where the shower is located. Here’s how to change a shower drain in 8 steps.

1. Cut into the drywall underneath your shower

To begin work on your shower drain, turn off all circuit breakers that control the lights and outlets in the bathroom you’re working on. Wearing a headlamp for light optimizes safety until you feel confident you know where all the wires are located.

Next, make a rectangular hole in the drywall underneath your shower with a drywall saw and utility knife. Be cautious of any other pipes or wires that may be in the ceiling as well. Continue your cut as far as the ceiling joists on either side. Then, cut down the middle of the joists to provide a backing for the new drywall. Make sure the hole is rectangular as this shape will be easier to patch than any other.

The section should also be large enough to allow you to disassemble your drain. If your shower drain has been leaking, the best place to cut is where the drywall is soggy, or water is dripping. Cut away all the water-damaged and moldy drywall.

Disassemble the interior shower drain

This portion of the process is complex and requires several mechanical steps to begin disassembling the portion of the drain inside the shower.

First, wedge a flat-head screwdriver under the drain strainer and pry it up. Next, remove the strainer so the locknut and gasket inside the drain flange are exposed. You’ll see that the locknut has several crowns. Put a screwdriver against one of the crowns and tap the screwdriver with a hammer to turn the nut clockwise. Then, keep tapping until you’re able to turn the nut by hand. Unscrew the crown and remove it. Finish prying out the rubber gasket underneath it with the screwdriver.

Remove the drain locknut from beneath the shower

Return to the space beneath the shower (either the ceiling or the crawl space) and locate the locknut holding the drain to the shower pan. If space is available, you can use wide-jaw pliers to loosen it. However, if space is limited, then use the same technique described above (i.e., tapping one of its crowns counterclockwise with a screwdriver and hammer until the nut is loose enough to turn by hand).

Prepare the waste pipe for a new drain

Before attaching the new drain, wipe the rim of the waste pipe off with a rag. You want to make sure it’s clear of any stray putty or debris before sliding on the locknut, then the fiber gasket, and finally the rubber gasket for the new drain.

To attach these new fixtures, you’ll likely have to pull the pipe away from the drain opening. Once you’ve done this, make sure you return the drain to its original position.

Install a new drain flange

Before installing a new drain flange, wipe away old plumbers’ putty and check the shower floor around the drain opening. If cracks are present, you may need to install a new shower pan before continuing.

If no cracks are present, continue by packing the underside of the rim of the new shower drain flange with plumbers’ putty. Do this by rolling the putty into a rope and winding the rope around the flange. Then, flatten it with your fingers.

https://copperlab.com/blogs/guides/how-to-replace-shower-drain

We are very curious about How to Install a Shower Drain and I really hope you enjoyed the new entry. Sharing is caring. You never know, you might be doing someone a favor. Thank-you for going through it.

Report this page